Sanyo PLC-WL2500 Bedienungsanleitung

Wired SettingProjector Set-up and OperationOwner’s ManualNetwork Set-up and Operation This is the manual for the Network function. Read this manual t

10Chapter 1 Preparation

ENGLISH11ENGLISHChapter 2 Setup Procedures2Describes how to configure the network.

12Chapter 2 Setup ProceduresSetting procedures and contents differ depending on the LAN installation location. When installing, consult your system a

13ENGLISH Network configuration*1 Set "On" only when the DHCP server is available on your network environment.*2 Set [255.255.255.255] if th

14Chapter 2 Setup ProceduresThe Network PIN code is to restrict the access to the projector through the network.After setting the Network PIN code, yo

15ENGLISH Network factory defaultNetwork factory default1. Select “Network factory default” in the Network menu and press SELECT button.2. A confirmat

16Chapter 2 Setup ProceduresWired LAN factory default settingsParameterSELECTED LANLAN 1 LAN 2 LAN 3DHCP OFF ON OFFIP ADDRESS169.254.100.100 192.168.1

ENGLISH17ENGLISHChapter 3 Basic Setting and Operation3Describes basic operations and settings for controlling the projec-tor by using the web bro

18Chapter 3 Basic Setting and OperationLogin the setting page of the projector[1] Enter the IP addressLaunch the web browser installed in your compute

19ENGLISH [3] Display of main setting pageThe following main setting page will be displayed according to your display mode selection. Perform v

2ComplianceFederal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pu

20Chapter 3 Basic Setting and OperationHow to use the setting pageTo control and set up the projector, use the setting menus on the web browser. Descr

21ENGLISH How to use the setting pageRadio button settingSelect an item by selecting a radio button.Check box settingSelect items by ticking on check

22Chapter 3 Basic Setting and OperationInitial settingAfter installing the projector, perform the following basic initial setting.Click Initial Settin

23ENGLISH Initial settingNetwork PIN code settingThis is to set the Network PIN code to restrict the access from an unauthorized person through t

24Chapter 3 Basic Setting and OperationNetwork configurationClick Network on the main menu. The following setting page is displayed. The IP Address, S

25ENGLISH E-mail settingThis projector has an E-mail function which can send an alert message to users or an administrator if it detects an abn

26Chapter 3 Basic Setting and Operation2 Registering and deleting E-mail addressesEnter the e-mail address onto "Add e-mail address" and

27ENGLISH E-mail setting✐"When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby i

28Chapter 3 Basic Setting and Operation● When PJ lamp replacement time is reached:✐ Replace it with a new lamp immediately and reset the lamp counter

29ENGLISH SNMP settingThis projector provides a SNMP (Simple Network Management Protocol) agent function. The SNMP consists of a manager an

3ENGLISH Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS● When you find a problem with the projector, remove the power cab

30Chapter 3 Basic Setting and OperationCheck and delete the trap addressChecking the registered trap address and deleting the address.To delete t

ENGLISH31ENGLISHChapter 4 Controlling the Projector4Describes controlling and setting of the projector by using the web browser.

32Chapter 4 Controlling the ProjectorPower control and status check Click Power & Status on the main menu. The control page will be dis-playe

33ENGLISH About projector conditionStatus DescriptionNormal ... Projector is operating no

34Chapter 4 Controlling the ProjectorControlClick Control on the main menu. The setting method differs depending on the contents of the page. Click

35ENGLISH SystemThis function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu

36Chapter 4 Controlling the ProjectorSound This function is to adjust the sound of the projector. The values in the text box represent the curren

37ENGLISH Item DescriptionContrast ... Adjusts picture con-trast (0~ 63)Brightness ... Adjusts pict

38Chapter 4 Controlling the ProjectorPC adjustmentClick PC Adj. on the main menu. This function is to adjust the signal from the computer connected t

39ENGLISH Setting up the projectorClick Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting] or

4Compliance ...

40Chapter 4 Controlling the ProjectorItem DescriptionCeiling ... Sets the image top/bottom and left/right reversed. (ON, OFF)Rear .

41ENGLISH Setting up the projectorItem DescriptionKey lock ... Sets the prohibition of controls either Projector or Remote control. (O

42Chapter 4 Controlling the ProjectorInformationThis page is to display the basic information of the projector status. Click Information on the main

ENGLISH43ENGLISHChapter 5 Appendix 5Connection examplesUse of telnetWeb browser settingTechnical dataQ & A

44Chapter 5 AppendixExamples of connectionPeer-To-Peer connectionConnecting the projector (PJ01) to the control computer (PC05) directly.Projector Nam

45ENGLISH The gateway (Router) installed in the networkConnecting the projector (PJ01) to the control computer (PC05) via the gateway.To another netwo

46Chapter 5 AppendixUse of telnetYou can control the projector by using the telnet application*1 installed on your computer. Normally, the telnet app

47ENGLISH 3. When communication is established correctly, the word "PASSWORD:" appears on the window. Type the login password (Network P

48Chapter 5 AppendixWeb browser settingThis projector is designed to be set up and controlled from an Internet web browser. Depending on the

49ENGLISH Examples: OS/BrowsersWindows XP ProfessionalInternet Explorer v.6.0ActiveScript settingSelect Internet Options from Tools menu on the web br

ENGLISH5ENGLISH1Chapter 1 PreparationDescribes features and operating environment of this projector.

50Chapter 5 AppendixProxy settingSelect Internet Options from Tools menu on the web browser and then select Connection tab and click LAN S

51ENGLISH Web browser settingNetscape Navigator v.7.1JavaScript SettingSelect Preference from Edit menu on the web browser a n d th e n s e

52Chapter 5 AppendixMAC OS X v 10.4Safari v.3.2.1JavaScript enable settingSelect Preferences... from Safari on the web browser and then select S

53ENGLISH Q&AQ&AInstallation/AccessQ Why doesn’t the setting page appear in my web browser?A Following causes are possible. Please check them.

54Chapter 5 AppendixQ We use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment?A Pos

55ENGLISH Q&AOperationQ Why can't be turned on/off with web browser?A Please make sure the settings of the projector are correct to

56Chapter 5 AppendixOthersQ What are the rules for IP address assignment?A If the network is constructed with TCP/IP protocol, a unique IP address is

57ENGLISH Q&AQ Can I update the firmware of the projector.A It is possible to update the firmware through the network. It is required to have a

NETWORK OWNER'S MANUALSO-KJ8ADSANYO Electric Co., Ltd.

6Chapter 1 PreparationFeaturesE-Mail Alert function (+p.25)T h e p roje c to r sen ds mes-sages to the registered e-mail addresses when a lamp

7ENGLISH FeaturesRequired operating environment for computersWhen operating the projector via networks, computers should meet the operating envi-ronme

8Chapter 1 PreparationThe limitation*1 of connection between the projector and hub or computer Suitable LAN cables are limited by length and type as f

9ENGLISH Flow of installationFlow of installationTo use the projector via the networks, follow the setup procedures below.STEP 1Connect the LAN and se