Sanyo SRC-850 Bedienungsanleitung

INSTRUCTION MANUALSRC-850Video Cassette Recorder EnglishMagnétoscope à Cassette FrançaisVideograbador EspañolPlease read this manual and accompanying

CHANGING THE ON-SCREEN DISPLAYChanging the Date/Time Display Position1 Turn the power on to all devices used.2 Set the ON SCREEN switch to the “ON” po

VIDEO CASSETTE TAPESUse only video cassette tapes bearing the w logo. ThisVCR was primarily designed for use with T-160 cassettetapes, it is recommend

VIDEO CASSETTE TAPESCorrect tape thread check functionIf the correct tape thread check function is on, after thecassette tape is loaded, a mechanism w

NORMAL RECORDINGNormal RecordingBefore Starting•Turn the power on to all devices used.•Load a cassette tape with erasure-prevention tab.NOTE:•If in th

NORMAL RECORDINGAction to Take when the Video SignalDeterioratesIf there is no video signal during recording, fast forward,rewind modes, when in stop

AUTOREPEAT RECORDINGAutorepeat RecordingThe same tape can be recorded over many times.•Follow the Before starting steps, under “NORMALRECORDING”.1 Pre

ALARM RECORDINGBy connecting the ALARM IN terminal to a door switch,an interphone, etc., a recording can be done only whennecessary.Alarm Recording Se

ALARM RECORDINGAlarm Recording Counter Display•During alarm recording, “AL” will be flashing on thedigital display.•If the ON SCREEN switch is set to

ALARM RECORDINGAlarm SearchTo go to the beginning of a desired alarm recording.1 Press the PAUSE/SEARCH button during stop mode.°“AL SEARCH 01” will b

SERIES RECORDINGUsing 2 VCRs or more, the series recording function letsyou switch recording from one unit to the next (only withVCRs of the same mode

PRECAUTIONSCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PAR

SERIES RECORDINGContinous Loop Recording SetupIt is possible to configure at least two this VCR forcontinous loop recording.Under loop recording when

NORMAL PLAYBACKNormal Playback1 Turn on the power to the VCR and TV monitor.2 Load the video cassette tape.3 Press the PLAY button.°Playback starts.°I

SPECIAL PLAYBACKPicture Search (Forward and Reverse)1 Press the FF (or REW) button, during normalplayback.°The image can be seen while the tape isadva

SETTING THE SECURITY LOCKThe security lock function is designed to preventaccidental stopping of recording if the STOP button ispressed inadvertenly.1

SETTING THE CASSETTE EJECT MODECassette Eject SetupWhen using 2 VCRs or more, the cassette tape of all theVCRs or some of the VCRs can be ejected, if

SETTINGS FOR RS485 TERMINALS USEThe VCR can be controlled through a special controllerconnected to the RS485 terminal.If the VCR is going to be contro

CHECKING POWER FAILURE, FAILURE DUE TOCONDENSATION AND USAGE DURATION1 Press the MENU button until the (POWER FAILURE),(DEW) and (USED TIME) menu is

OUTPUT TERMINALSTAPE END OUT Terminal•During recording, when the end of the tape is reachedor when the tape counter reading indicates 7 hours 57minute

OUTPUT TERMINALSSW OUT TerminalWhen recording, a pulse signal is output at the SW OUTterminal.This terminal is usually connected to the switch input (

OUTPUT TERMINALSREMOTE JackYou can use a VA-RMN01 Remote Control Unit (soldseparately) to control remotely the VCR.NOTE:•The functions not available o

FEATURES•Controllable through an RS-485 connection•High-speed Fast Forward/Rewind•8-hour mode recording•In 8-hour modes audio recording is available•A

MAINTENANCEDaily InspectionThe following daily inspections are recommended in orderto assure long-term and trouble-free operation of the unit.The dail

MAINTENANCEMaintaining and Checking The MechanismTo maintain the VCR functions and features working properly, and to avoid damages or dirt on the tape

TROUBLESHOOTING GUIDEIf the unit does not operate normally when you follow the instructions indicated in the manual, please refer to the tablebelow.SY

SPECIFICATIONSGeneral SpecificationsVideo heads system Dual-azimuth 4-head rotating helical scanning system: Dual azimuth 2-head for record and stand

SANYO INDUSTRIALVCR WARRANTYOBLIGATIONSIn order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Se

SANYO Electric Co., Ltd.1AC6P1P2047–AANU4Q/U3(1099KP-SY01) Issue No. 3 Copyright SANYO, 1999 All rights reserved. Printed in IndonesiaNU4Q/U3

LOCATIONS OF CONTROLS ANDINDICATORSFront Panel1EJECT button2 Cassette loading slot3 PAUSE/SEARCH button4REW (rewind) button5PLAY button6FF (fast forwa

LOCATIONS OF CONTROLS AND INDICATORSDigital Display1 Alarm indicatorFlashes when an alarm isbeing recorded: Comes on after the alarmhas been recorded

LOCATIONS OF CONTROLS AND INDICATORSBack Panel1 Battery compartment2 ALARM OUT (alarm output) terminal3 ALARM IN (alarm input) terminal4 COM (common)

CONNECTIONSConnect the video camera and monitor TV as shown in the figure below.NOTE: Before making the connections, make sure all the devices are dis

TYPES OF ON-SCREEN DISPLAYS ANDDISPLAY SEQUENCENOTES:•When a menu is displayed, recording will not be possible.•Press the PAUSE/SEARCH or MENU button,

SETTING THE LANGUAGE AND CLOCKLanguage SettingEnglish, French or Spanish can be selected by the user.1 Turn the power on to all devices used.2 Press t